Ford F-350 Powerstroke Cold Air Intake - Cotton Cleanable - 6.7L Diesel

Product Information

Your price: $329.99

Lowest Price Guaranteed

More info!

Average Rating

Brand:

S&B Filters

Available Options

Select quantity

Drive now, Pay later with Affirm

Learn More

or with PayPal

Both options will be available upon checkout.

Description Reviews You May Also Like About Manufacturer

Ford F-350 Powerstroke Cold Air Intake - Cotton Cleanable - 6.7L Diesel free shipping

MAXIMUM PERFORMANCE
This cold air intake for the 2020 Ford 6.7L Powerstroke was engineered to minimize air restriction and flow better than stock. This kit comes with a fully enclosed airbox that protects the filter from dirt and keeps out engine heat.

NEW SNAP IN LID DESIGN
The new snap-In lid design requires no screws to secure it to the box. This makes installation and inspection quick and easy, as the filter can be installed and removed without having to remove the intake tube. While silicone edge trim ensures an airtight seal, protecting against unwanted, power-robbing engine heat.

This kit comes with a massive, highly-efficient air filter which results in better performance and protects your engine. Available in either 8-layer Cotton Cleanable or Dry Extendable media.

LESS RESTRICTION. MORE AIRFLOW.
The Intake Tube has minimal bends as it connects to the turbo inlet. It is positioned in one clean line with minimum obstructions from the turbo inlet to the intake box and air filter. This results in a decrease in restriction compared to stock.

CHOOSE YOUR AIRFLOW.
The 75-5140 intake kit has two airflow configurations. S&B includes a silicone box plug that can be installed or removed depending on personal preference and airflow requirements.

Silicone Box Plug removed: This configuration will provide an extra air inlet that will be pulled from the passenger side fender area.

Silicone Box Plug installed: This configuration will seal the secondary air inlet located on the side of the box facing the vehicle fender. The front-facing grill inlet and the front scoop will become the main source of airflow into the Intake Box.

NO CHECK ENGINE LIGHTS
S&B devotes a huge amount of resources to engineer our intakes that allow your engine to run properly with stock calibration or enhanced tuning. An injection molded MAF plate in conjunction with a foam MAF sensor gasket ensures a true OE seal to the sensor.

CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Need Assistance?

We're here to help!

Call us at 512-982-9393 (Austin, TX) or
562-981-6800 (Signal Hill, CA)
and get assistance from one of our sales team members!

Product ID Number:

33115347

DIY Install Instructions

Click here for Installation Instructions for this product!

Lowest Price Guarantee

We price match and beat our competitors!

Shipping

We ship globally and offer multiple shipping item discounts.

About Manufacturer

S&B Filters is a manufacturer of cold air intakes, filters and other performance parts, specializing in diesel/gas trucks and SUVs. Holding true to our goal, we engineer intake systems to greatly reduce airflow restriction, while still protecting your engine and test our product against our competitors following ISO 5011 standards. We keep our quality high and our pricing low by making almost everything ourselves in the U.S.

Breathe easy. Your engine and warranty are protected.
A mountain of dust and our 1/2 million dollar lab is how far we've gone to make sure your investment is protected.

Tested to a higher standard.
S&B tests to the internationally accepted ISO 5011 Standard when testing for airflow, efficiency and capacity. This is the same protocol used by most of the large automakers.

Airflow testing shows us how we compare to stock and our competitors. The goal is to beat both.

We test for efficiency to make sure that your engine is protected from debris while sucking in even more air. Lastly, we monitor the capacity of the filter to see how much dirt it can hold before needing to be serviced.

Precision and accuracy.
Our environmental control system is top of the line. S&B strives for accuracy and repeatability. In order to have dependable results, you have to have tight control over the humidity, temperature and barometric pressure.

Better Airflow
It's important to know how we stack up against stock and our competitors in order to be the best. We mount each intake system on our test equipment to measure the airflow from zero to the max CFM of the vehicle. We then compare the results and make design changes until we have maximized the airflow while still protecting your engine.

Protect your engine.
While airflow is important, it is equally critical to insure that your investment is protected. To do so, we first determine the max CFM the vehicle will generate at wide open throttle as it is more difficult to stop dust the greater the airflow. We then start pulling this amount of air through the intake while literally shooting fine particles of dust at the filter. Any dust bypassing the filter will be caught in the absolute blanket to determine the efficiency.

Some competitors have testing done at low CFMs in order to show higher efficiency rates, so beware.

We're not kidding.
Our testing is so controlled that we even heat the absolute blankets pre and post testing in order to remove the humidity. The absolute blankets catch any dust that gets past the filter during testing in order to determine the efficiency rate.

Removing the humidity insures that you are only weighing what actually bypassed the filter. Protecting your engine while providing better airflow is our top priority.